A two-dimensional photonic crystal asymmetric Mach-Zehnder filter (AMZF) based on the self-collimation effect is studied by numerical simulations and experimental measurements in microwave region. A self-collimated beam is effectively controlled by employing line-defect beam splitters and mirrors. The measured transmission spectra at the two output ports of the AMZF sinusoidally oscillate with the phase difference of π in the self-collimation frequency range. Position of the transmission peaks and dips can be controlled by varying the size of the defect rod of perfect mirrors, and therefore this AMZF can be used as a tunable power filter.
©2010 Optical Society of America
Photonic crystals (PCs) are multidimensional periodic structures with periods of the order of electromagnetic wavelengths that can be designed by the photonic band theory . The most important property of PCs is the existence of photonic bandgaps (PBGs) in which light propagation is completely prohibited in any direction . Since PBGs of a PC provide a powerful way to control wave propagation, PCs have several potential applications to photonic integrated circuits (PICs) [3,4]. In particular, light can be controlled to propagate without diffraction along the incident direction of the source beam, which is called the self-collimation phenomenon of light in PCs [5,6]. It is known that the self-collimated beams can be bent at the crystal-air interface, and split into two beams by introducing defects in the PC [7–12]. Moreover, self-collimated beams can be crossed without cross talk, hence optical devices based on the self-collimating property of light beams in PCs have potential for high density PICs.
Recently, Zhao et al proposed a PC Mach-Zehnder interferometer (MZI) by utilizing the self-collimated beams . Despite the promising applications, there have been no studies on the wavelength filters for self-collimated beams. Since the self-collimation phenomenon occurs due to the dispersion properties of propagating modes in PCs, not due to the existence of PBGs, it is very difficult to couple the self-collimated beams with the defect modes, and the reflection at the ends of finite PC structures causes crucial performance problems of devices. For these reasons, it is hard to design the wavelength filters of high performance for self-collimated beams. Very recently, it is demonstrated that the unnecessary reflections at the interfaces between a PC and homogeneous background material are effectively minimized by adding antireflection structures (ARS) which can be optimized by varying the radii of rods (holes) of the ARS and the distance between the ARS and the PC truncation [13,14]. Using this method, it is possible to improve the performance of optical devices which make use of self-collimation of light in a PC.
In this paper, we propose a design of a 2D PC asymmetric Mach-Zehnder filter (PC-AMZF) based on the self-collimation effect in a 2D PC and experimentally demonstrate its transmission characteristics in microwave region. This PC-AMZF utilizes the property of self-collimated beams that can be effectively steered by employing line-defect beam splitters and mirrors. Unwanted reflections at the interfaces between a uniform dielectric and the 2D PC is suppressed by introducing the ARS at the input and output interfaces of the PC. Also it is demonstrated that the geometric modification of the perfect mirrors based on the Goos- Hänchen (GH) shift  makes the control of the peak frequencies possible. The GH shift was shown experimentally utilizing the self-collimated beam reflected from the surface of a 2D PC and a method for controlling the beam reflection was proposed by modifying the size of surface rods [16,17]. The measured transmission spectra are compared with the numerical ones obtained by the finite-difference time-domain (FDTD) simulations .
2. Design and operation principle
The basic AMZF composed of two 50:50 beam splitters and two totally reflecting mirrors is shown in Fig. 1 . When a light beam of intensity I0 is launched into the input port of AMZF, the two beam splitters result in four self-collimated beams, each with intensity I0/4 at the output side beam splitter BS2. At each of the two output ports, two self-collimated beams with the intensity I0/4 each are added and interfere, and the resulting output intensities are given by3].
3. Experimental setup
The experimental layout, depicted in Fig. 2(a) , consists of a network analyzer (Agilent HP8720B) and two microwave horn antennas (ETS Lindgren 3160-08). The source and receiver horn antennas are set to pass TM (the electric field parallel to the axes of alumina rods) polarized microwaves. The resulting frequency-dependent data were normalized with the transmittance measured without the PC sample to remove any loss or other problems caused by cables or connecting parts of the setup. The 2D PC sample composed of alumina is constructed by boring holes through two aluminum plates which are separated by spacers. These two parallel aluminum plates can ensure TM polarized microwaves . The 2D PC-AMZF shown in Fig. 2(b) is composed of square array of cylindrical rods in air with two 50:50 beam splitters and two perfect mirrors. A first band gap of this structure ranges from 14.39 to 19.92 GHz. The cylindrical rods of the radius r = 2 mm, length l = 100 mm, and the lattice constant a = 5 mm, are made of alumina with the dielectric constant of ε ≈9.7. The line-defect beam splitters BS1 and BS2 are composed of 17 rods arrayed in the ΓΧ direction with the radius rd different from those of host rods. The perfect mirrors M1 and M2 are made by removing two rows of 17 rods along the ΓΧ direction. The components BS2 and M2 are oriented along the opposite ΓΧ direction with the components BS1 and M1. ARS with the radius of rods RARS = 1.15 mm is introduced at the input and output interfaces of the PC-AMZF to minimize the coupling loss. The distance dARS between the ARS and the PC-AMZF truncation is 3.60 mm [13,14]. From our previous work we found that this PC structure has a self-collimation region for electromagnetic waves of frequencies around 12.5 GHz along the ΓM direction . In order to make the 50:50 beam splitter, we obtained the transmitted and bent powers using the FDTD simulations varying the radius of one-row line defect, rd from 0.5 to 2.5 mm as shown in Fig. 2(c). The result obtained is shown in Fig. 2(d) and one can observe that when rd = 1.5 mm, the bent and transmitted powers become equal.
4. Result and discussion
To check the performance of the ARS, we measured the transmission spectra of the PC sample with and without the ARS and the results are displayed in Fig. 3 . The measured spectra are compared with the numerically obtained ones and a good agreement exists between the two. When the ARS is not introduced, as depicted in Fig. 3(a), the transmitted light powers at port 1 and port 2 through the PC exhibit the transmission minima at the frequencies 12.44 and 12.67 GHz, respectively. Because of unwanted reflections at the interfaces between the 2D PC and the outside medium it is not possible to use this structure as a filter in this frequency region. However, in Fig. 3(b), one can observe transmission peaks at the frequencies f1 = 12.67 GHz for port 1 and at f2 = 12.44 GHz for port 2, respectively in the frequency range from 12.3 to 12.8 GHz. This figure shows that the transmitted intensities at the two output ports oscillate sinusoidally with a phase difference of π. Besides the sinusoidal oscillations of the two output intensities, the performance of the PC-AMZF is significantly improved by the introduction of the ARS into the PC. With the ARS attached, almost 92% of the incident power is transmitted through the AMZF at the frequencies f1 and f2, and this value is more than 30% improved result compared with the case of the ARS not applied to the AMZF. The steady-state electric field distributions of the self-collimated beams which are obtained by the FDTD simulations are shown in Fig. 3(c) for the light of frequency f1 and in Fig. 3(d) for f2, respectively. It clearly displays that if the two light beams of frequencies f1 and f2 are synchronously inserted into the input port, the proposed PC-AMZF can separate them into two groups such that the light beam of frequency f1 is emitted through port 1 and that of the frequency f2 through port 2.
Furthermore, we investigated the effect of geometric modification of the perfect mirrors. As illustrated in Fig. 4(a) , two rows of 17 rods are removed along the ΓΧ direction out of the PC matrix and additionally, the radius of one row of rods on the front side surface, rm is varied from 1.75 mm to 1.95 mm. When a self-collimated beam is reflected by this modified mirror, it is predicted that the phase shift is altered compared with that produced by the unmodified mirror. In the previous work, it is shown that varying the radius of the surface rods changes the effective index of the surface layer of the mirror which is caused by the change in the filling fraction of the dielectric material . Manipulation of the surface geometry or the refractive index of perfect mirror can change the duration of the confinement of power on the surface and therefore the GH shift can be modified. The measured and simulated transmission spectra for the modified mirrors are plotted in Figs. 4(b), 4(c) and 4(d) for different values of rm. It is observed that as the value of rm decreases, the peak frequencies shift to higher values. These results prove that it is possible to control the peak frequencies of light beams emitting out of the two output ports by adjusting the value of rm.
In conclusion, we propose a design of a 2D PC-AMZF based on the self-collimation effect and experimentally show its transmission properties in microwave region. The ARS with the optimized parameters can effectively eliminate unnecessary reflections at the 2D PC-AMZF and thus the performance of a PC-AMZF can be significantly improved. It is shown that the measured transmission spectra at the two output ports sinusoidally oscillate with the phase difference of π, and therefore the proposed AMZF can effectively separate incoming self-collimated beams into two different output ports. Also demonstrated is that tuning of the peak frequencies can be achieved by modifying the geometry of the perfect mirrors. We expect that the proposed PC-AMZF can also be applied in the optical wavelengths region as well.
This work was partially supported by National Research Foundation of Korea Grant funded by the Korean Government (R11-2008-095-01000-0).
References and links
1. J. D. Joannopoulos, R. D. Meade, and J. N. Winn, Photonic Crystals: Molding the Flow of Light (Princeton University Press, NJ, 1995).
2. S. G. Johnson, P. Villeneuve, S. Fan, and J. Joannopoulos, “Linear waveguides in photonic-crystal slabs,” Phys. Rev. B 62(12), 8212–8222 (2000). [CrossRef]
3. D. Zhao, J. Zhang, P. Yao, X. Jiang, and X. Chen, “Photonic crystal Mach-Zehnder interferometer based on self-collimation,” Appl. Phys. Lett. 90(23), 231114 (2007). [CrossRef]
5. H. Kosaka, T. Kawashima, A. Tomita, M. Notomi, T. Tamamura, T. Sato, and S. Kawakami, “Superprism phenomena in photonic crystals,” Phys. Rev. B 58(16), R10096–R10099 (1998). [CrossRef]
6. J. Witzens, M. Loncar, and A. Scherer, “Self-collimation in planar photonic crystals,” IEEE J. Sel. Top. Quantum Electron. 8(6), 1246–1257 (2002). [CrossRef]
8. D. W. Prather, S. Shi, D. M. Pustai, C. Chen, S. Venkataraman, A. Sharkawy, G. J. Schneider, and J. Murakowski, “Dispersion-based optical routing in photonic crystals,” Opt. Lett. 29(1), 50–52 (2004). [CrossRef] [PubMed]
9. D. M. Pustai, S. Shi, C. Chen, A. Sharkawy, and D. W. Prather, “Analysis of splitters for self-collimated beams in planar photonic crystals,” Opt. Express 12(9), 1823–1831 (2004). [CrossRef] [PubMed]
10. S.-G. Lee, S. S. Oh, J.-E. Kim, H. Y. Park, and C.-S. Kee, “Line-defect-induced bending and splitting of self-collimated beams in two-dimensional photonic crystals,” Appl. Phys. Lett. 87(18), 181106 (2005). [CrossRef]
11. M.-W. Kim, S.-G. Lee, T.-T. Kim, J.-E. Kim, H. Y. Park, and C.-S. Kee, “Experimental demonstration of bending and splitting of self-collimated beams in two-dimensional photonic crystals,” Appl. Phys. Lett. 90(11), 113121 (2007). [CrossRef]
13. X. Yu and S. Fan, “Bends and splitters for self-collimated beams in photonic crystals,” Appl. Phys. Lett. 83(16), 3251 (2003). [CrossRef]
14. T.-T. Kim, S.-G. Lee, M.-W. Kim, H. Y. Park, and J.-E. Kim, “Experimental demonstration of reflection minimization at two-dimensional photonic crystal interfaces via antireflection structures,” Appl. Phys. Lett. 95(1), 011119 (2009). [CrossRef]
16. A. F. Matthews and Y. S. Kivshar, “Tunable Goos-Hänchen shift for the self-collimated beams in two-dimensional photonic crystals,” Phys. Lett. A 372, 3098–3101 (2008).
17. A. F. Matthews and Y. S. Kivshar, “Experimental studies of the internal Goos-Hänchen shift for self-collimated beams in two-dimensional microwave photonic crystals,” Appl. Phys. Lett. 93(13), 131901 (2008). [CrossRef]
18. A. Taflove, Computational Electrodynamics: The Finite-Difference Time-Domain Method, (2nd Ed. Artech House INC, Norwood, 2000).
19. D. M. Pozar, Microwave Engineering, (John Wiley & Sons, New York, 1998), Chap. 3.2.