Abstract
We present a passively mode-locked Yb:CALGO oscillator with harmonic repetition rate operation up to the third order. It is operated in the solitary regime with a fundamental roundtrip rate of 94 MHz and pulse durations between 200 fs and 600 fs. Harmonic operation was observed being stable for several days. The harmonic mode-locking regions are analyzed depending on intra-cavity dispersion. The transient pulsing dynamics converging to the stable harmonic modes is tracked and a theoretical model describing the pulse moving mechanisms is presented.
© 2017 Optical Society of America
1. Introduction
Harmonic mode-locking operation enables high repetition rates from long resonators with easy set-up. It is well known from fiber laser technology [1, 2], in which harmonic frequencies are typically imposed by intra-cavity phase [3] or amplitude [4] modulation or passively by colliding-pulse harmonic mode-locking [5]. Solid-state lasers have been harmonically mode-locked with intra-cavity phase modulation of a Nd:YAG rod laser [6] or passively with diode-pumped and SESAM mode-locked laser system [7, 8], or by using an etalon [9] or the coupled-cavity effect [10].
In this work, a SESAM mode-locked diode-pumped Yb:CaGdAlO4 (Yb:CALGO) bulk oscillator producing femtosecond pulses at a fundamental repetition rate of ffund = 94 MHz is presented. By increasing the pump power, second harmonic mode-locking operation with a repetition rate of f2nd−harm = 188 MHz and third harmonic at f3rd−harm = 282 MHz is observed. For this operation no means of active stabilization is required. A suppression of the fundamental radio frequency signal at second harmonic operation with more than 88 dBc and at third harmonic with more than 71 dBc verifies the quality of this operation regime. Long-term passive stability was observed for over 160 h. In order to trace the multi-pulse dynamics, the pulse evolution from pulse splitting up to the second harmonic stable operation was tracked with a fast photo diode and a fast real-time oscilloscope. In order to understand the high quality of passive harmonic mode-locking, a numerical model is presented which describes the divergence of two initially closely-spaced pulses based on the gain evolution. The presented results indicate the mechanisms of harmonic mode-locking and compose a concept for bulk material based systems, which are further scalable in power and repetition rate.
2. Experimental setup
The oscillator, shown in Fig. 1, is based on an a-cut Yb:CALGO crystal of 1.5 mm thickness and a Yb doping of 5 %. Yb:CALGO has a broad and smooth absorption cross section with a maximum at 979 nm [11–13]. It provides a broadband emission plateau for the laser regime between 1000 and 1050 nm [12–14], which would allow for pulse durations down to 32 fs [15–17].
A fiber-coupled 30 W diode laser with a 200 µm core diameter (JENOPTIK, JOLD-30-FC-12-980) is imaged 1:1 into the 138 µm resonator beam waist (1/e2 radius) inside the crystal for pumping. For an optimized absorption of pump light the emitted wavelength of the laser diode was shifted to 979 nm by controlling the operating temperature. A polarized beam splitter and a motorized half-wave plate were used to variably control the pump power. A second lambda-half plate was used to optimize the pump absorption. The cavity was set-up by highly reflective (HR) and Gires-Tournois interferometer (GTI) dispersive mirrors. To induce mode-locking, a semiconductor saturable absorber mirror (SESAM, BATOP GmbH, SAM-1040-1-500fs) was installed at one cavity end. It is specified with a high reflectivity from 1020 nm to 1100 nm, a zero group delay dispersion (GDD) from 1040 nm to 1070 nm, a modulation depth of 0.6 %, non-saturable losses of 0.4 %, a saturation fluence of 120 µJ/cm2, and a relaxation time constant of about 500 fs. As second end mirror a 2.4 % output coupler is employed. We operate the oscillator in the solitary regime at negative GDD. The GTI mirrors can be chosen for a net GDD of D2 = −420 fs2, −1470 fs2 or −2680 fs2 per round trip. A sapphire plate in Brewster’s angle is used to operate the oscillator in p-polarization. The total resonator length of 3.2 m provides a fundamental repetition rate of frep = 94 MHz. Depending of the intracavity GDD, pulse durations at full width at half maximum (FWHM) from τFWHM = 605 fs down to τFWHM = 190 fs have been observed.
3. Experimental results
For increasing pump powers at the different GDD values, pulse duration, optical spectrum, and the radio frequency (RF) spectra have been recorded. The red crosses in Figure 2(a)–2(c) show the pulse durations as a function of the intra-cavity average power for the three different dispersion regimes. The label I indicates the single, II the double, and III the triple pulsing regime, respectively. At approximately Pint,−2680 = 132 W, Pint,−1470 = 80 W and Pint,−420 = 37 W of intracavity average power, indicated by red lines in the figures, the single pulse splits into two pulses, and the pulse duration jumps to maintain the solitary condition. Beyond around Pint,−1470 = 130 W and Pint,−420 = 64 W three pulses oscillate. This solitonic pulse splitting is well-known as an effect stemming from two-photon absorption in the SESAM [18–20]. Beyond Pint,−420 = 70 W Q-switching led to damage on the SESAM. Table 1 summarizes the average output power Pout, the pulse durations τFWHM, the pulse energies Eout, and the output peak powers Pmax,out for the individual pulses at different GDD D2. Going to harmonic orders beyond three was limited by the pump power in the high dispersion regime and by SESAM damage at −420 fs2. For a short time only, fourth harmonic mode-locking at −630 fs2, with an average power of 3.26 W, 240 fs pulse duration and a sideband suppression better than 75 dBc was observed; however, this regime was quite sensitive to the focal position on the SESAM and is therefore disregarded in the following.
After pulse splitting, stabilization of the multiple pulses at the harmonic distances was observed. The color maps in Figure 2(a)–2(c) visualize radio frequency spectra for the three different dispersion values. The extinction of certain harmonic lines in the RF spectrum indicates high-fidelity harmonic mode-locking. Figure 3(a) reveals 88 dB of suppression in 1 Hz resolution bandwidth; Fig. 3(b) shows the third harmonic with 71 dB suppression.
The long-term passive stability of the harmonic mode-locking operation can be demonstrated by tracking the suppressed second harmonic peak in the RF signal with a 1 Hz resolution. This is shown in Fig. 4 for more than 160 hours of laser operation.
The pulse splitting was accompanied by a systematic shifting of the optical spectra in agreement with Zhou et al. [8].
In Figure 5(a), the optical spectra (color map) and the center frequencies (red dots) follow the resonator internal average power in the three mode-locking regimes. This is directly attributed to the solitary pulsing condition [21–23]
with the single path length l and nonlinear refractive index n2 of the laser crystal, and the mode area Aeff inside. is the fundamental repetition rate with the round trip time TR and an integer number m for the harmonic order. Figure 5(b) shows individual spectra for 51 W (red), 83 W (green), 100 W (blue), 135 W (purple) and 144 W (black) of internal power. Invisible Kelly sidebands emphasize the quality of the soliton pulsing.In order to understand the dynamics of the split pulses we tracked the temporal evolution with a fast photo diode and a real-time oscilloscope with 16 GHz bandwidth and 50 GS/s sampling rate (Tektronix DPO71604C). It was used in the "FastFrame"-mode with a dead time of 200 µs between the measured frames. Figure 6 shows a typical pulse splitting event and the slow temporal separation of both pulses until after about four seconds the stable position at half of the round trip time (red dashed line) is reached. The pulses stabilize their temporal position according to the second harmonic of the repetition rate without any active control. Particularly interesting is the observation of certain temporal plateaus during the transient. They correspond to the effective optical path lengths between specific resonator components: The lowest plateau indicates the collision of two pulses on mirror GTI1 (see Fig. 1). The second plateau is attributed to the collision in the crystal, and the third to mirror HR5. On these components, the two pulses collide and interact, e.g., via nonlinear coupling in the gain medium [24] and/or scattering at the mirrors. All surfaces inside the resonator might give rise for building a plateau, and other measured transients show other plateaus. It is unclear why certain components surfaces stabilize the pulse positions during one transient, during another not.
4. Theoretical model
In accordance to Zhou et al. [8], the final harmonic arrangement of the pulses is attributed to the gain dynamics. To understand the relative motion of two pulses in the resonator we adapted a theoretical model based on the Master equation of mode-locking and the split-step Fourier method [25–29]:
Here, g(T, t) is the power gain, Ωg the spectral width of the gain profile, q(T, t) the absorber losses, and A(T, t) the slowly varying field envelope. The following two equations govern the gain evolution g(t) and the absorber losses q(t): with the upper-state lifetime of the laser material τL, the small-signal gain g0, the saturation energy of the gain material Esat,L, the relaxation time of the absorber τA, the non-saturable absorption q0, and the saturation energy of the absorber Esat,A.Figure 7 reveals the evolution of the gain (red) and the total losses (green) together with the pulse (blue) in the double pulse regime. Here, for clarification of the effect, the repetition time was reduced to TR = 1 ns. Further parameters are: Esat,L = 6.8 mJ, , Aeff = 5.7 · 10−8 m2, λ = 1050 nm, τL = 380 µs, , Esat,A = 0.88 nJ, D2 = 550 fs2, τA = 850 fs, q0 = 1 %, and l = 0.5 %. The higher gain for the leading pulse results in a–slightly higher gain gradient giving rise to a very slow relative pulse motion away from each other. At the distance of half the round trip, the gain and the gradient become symmetrical and the pulses stabilize (see Fig. 6).
5. Conclusion
A harmonically mode-locked Yb:CALGO laser oscillator is presented, featuring harmonics of the repetition rate up to the third order, limited only by pump power. Harmonic operation is demonstrated with exceptionally high fidelity and long-term stability for more than 160 h. The transient evolution of the pulse positions and the convergence against the steady harmonic state have been experimentally tracked, and the dynamics have been explained by a gain evolution model. This is easily transferable also to other gain media. Based on this technique, high power, high-repetition rate oscillators with an simply implementable set-up long resonator are available.
Funding
Deutsche Forschungsgemeinschaft (Mo850/17-1); Nieders. Vorab (ZN3061, HYMNOS).
References and links
1. A. B. Grudinin, D. J. Richardson, and D. N. Payne, “Passive harmonic modelocking of a fibre soliton ring laser,” Electron. Lett. 29(21), 1860–1861 (1993). [CrossRef]
2. A. B. Grudinin and S. Gray, “Passive harmonic mode locking in soliton fiber lasers,” J. Opt. Soc. Am. B 14(1), 144–154 (1997). [CrossRef]
3. C. X. Yu, H. A. Haus, E. P. Ippen, W. S. Wong, and A. Sysoliatin, “Gigahertz-repetition-rate mode-locked fiber laser for continuum generation,” Opt. Lett. 25(19), 1418–1420 (2000). [CrossRef]
4. T. F. Carruthers, I. N. Duling, and M. L. Dennis, “Active-passive modelocking in a single-polarisation erbium fibre laser,” Electron. Lett. 30(13), 1051–1053 (1994). [CrossRef]
5. Y. Deng, M. Koch, F. Lu, G. Wicks, and W. Knox, “Colliding-pulse passive harmonic mode-locking in a femtosecond Yb-doped fiber laser with a semiconductor saturable absorber,” Opt. Express 12(16), 3872–3877 (2004). [CrossRef] [PubMed]
6. M. F. Becker, D.J. Kuizenga, and a.E. Siegman, “Harmonic Mode Locking of the Nd:YAG Laser,” IEEE J. Quantum Electron. 8(8), 687–693 (1972). [CrossRef]
7. S. Pekarek, C. Fiebig, M. C. Stumpf, A. E. H. Oehler, K. Paschke, G. Erbert, T. Südmeyer, and U. Keller, “Diode-pumped gigahertz femtosecond Yb:KGW laser with a peak power of 3.9 kW.,” Opt. Express 18(16), 16320–16326 (2010). [CrossRef] [PubMed]
8. W. Zhou, X. Fan, H. Xue, R. Xu, Y. Zhao, X. Xu, D. Tang, and D. Shen, “Stable passively harmonic mode-locking dissipative pulses in 2 µm solid-state laser,” Opt. Express 25(3), 1815–1823 (2017). [CrossRef]
9. Y. F. Chen, W. Z. Zhuang, H. C. Liang, G. Whuang, and K. W. Su, ‘High-power subpicosecond harmonically mode-locked Yb:YAG laser with pulse repetition rate up to 240 GHz,” Laser Phys. Lett. 10(1), 015803 (2013). [CrossRef]
10. T. W. Wu, C. H. Tsou, C. Y. Tang, H. C. Liang, and Y. F. Chen, “A high-power harmonically self-mode-locked Nd:YVO 4 1.34- µm laser with repetition rate up to 32.1 GHz,” Laser Phys. 24(4), 045803 (2014). [CrossRef]
11. T. Südmeyer, C. Kränkel, C. R. E. Baer, O. H. Heckl, C. J. Saraceno, M. Golling, R. Peters, K. Petermann, G. Huber, and U. Keller, “High-power ultrafast thin disk laser oscillators and their potential for sub-100-femtosecond pulse generation,” Appl. Phys. B 97(2), 281–295 (2009). [CrossRef]
12. P. O. Petit, P. Goldner, B. Viana, J. Boudeile, J. Didierjean, F. Balembois, F. Druon, and P. Georges, “Diode pumping of Yb3+:CaGdAlO4,” Proc. SPIE 6998, 69980Z (2008). [CrossRef]
13. J. Boudeile, F. Druon, M. Hanna, P. Georges, Y. Zaouter, E. Cormier, J. Petit, P. Goldner, and B. Viana, “Continuous-wave and femtosecond laser operation of Yb:CaGdAlO_4 under high-power diode pumping,” Opt. Lett. 32(14), 1962–1964 (2007). [CrossRef] [PubMed]
14. J. Petit, Ph. Goldner, and B. Viana, “Laser emission with low quantum defect in Yb: CaGdAlO4,” Opt. Lett. 11(30), 1345–1347 (2005). [CrossRef]
15. Y. Zaouter, J. Didierjean, F. Balembois, G. Lucas Leclin, F. Druon, and P. Georges, “47-fs diode-pumped Yb 3 +: CaGdAlO 4 laser,” Opt. Lett. 31(1), 119–121 (2006). [CrossRef] [PubMed]
16. A. Agnesi, A. Greborio, F. Pirzio, G. Reali, J. Aus der Au, and A. Guandalini, “40-fs Yb3+:CaGdAlO4 laser pumped by a single-mode 350-mW laser diode,” Opt. Express 20(9), 10077–10082 (2012). [CrossRef] [PubMed]
17. P. Sévillano, P. Georges, F. Druon, D. Descamps, and E. Cormier, “32-fs Kerr-lens mode-locked Yb:CaGdAlO4 oscillator optically pumped by a bright fiber laser,” Opt. Lett. 39(20), 6001–6004 (2014). [CrossRef] [PubMed]
18. M. J. Lederer, B. Luther-Davies, and H. H. Tan, “Multipulse operation of a Ti: sapphire laser mode locked by an ion-implanted semiconductor saturable-absorber mirror,” J. Opt. Soc. Am. B 16(6), 895–904 (1999). [CrossRef]
19. J. M. Soto-Crespo and N. N. Akhmediev, “Multisoliton regime of pulse generation by lasers passively mode locked with a slow saturable absorber,” J. Opt. Soc. Am. B 16(4), 674–677 (1999). [CrossRef]
20. R. Grange, M. Haiml, R. Paschotta, G. J. Spühler, L. Krainer, M. Golling, O. Ostinelli, and U. Keller, “New regime of inverse saturable absorption for self-stabilizing passively mode-locked lasers,” Appl. Phys. B 80(2), 151–158 (2005). [CrossRef]
21. T. Brabec, C. Spielmann, and E. Krausz, “Mode locking in solitary lasers,” Opt. Lett. 16(24), 1961–1963 (1991). [CrossRef] [PubMed]
22. F. Krausz, M. E. Fermann, T. Brabec, P. F. Curley, M. Hofer, M. H. Ober, C. Spielmann, E. Wintner, and A. J. Schmidt, “Femtosecond Solid-State Lasers,” IEEE J. Quantum Electron. 28(10), 2097–2122 (1992). [CrossRef]
23. C. Spielmann, P. F. Curley, T. Brabec, and F. Krausz, “Ultrabroadband Femtosecond Lasers,” IEEE J. Quantum Electron. 30(4), 1100–1114 (1994). [CrossRef]
24. M. Lai, J. Nicholson, and W. Rudolph, “Multiple pulse operation of a femtosecond Ti: sapphire laser,” Opt. Commun. 142(1), 45–49 (1997). [CrossRef]
25. G.P. Agrawal, Nonlinear Fiber Optics (Academic Press, 2005).
26. H. Haus, “A Theory of Forced Mode Locking,” IEEE J. Quantum Electron. 11(7), 323–330 (1975). [CrossRef]
27. H. Haus, “Theory of mode locking with a fast saturable absorber,” Appl. Phys. 46(7), 3049–3058 (1975). [CrossRef]
28. H. Haus, “Theory of mode locking with a slow saturable absorber,” IEEE J. Quantum Electron. 11(9), 736–746 (1975). [CrossRef]
29. F. X. Kärtner, I. D. Jung, and U. Keller, “Soliton mode-locking with saturable absorbers,” IEEE J. of Selected Topics in Quantum Electronics 2(3), 540–556 (1996). [CrossRef]