Abstract
We demonstrate the high-efficiency generation of water-window soft x-ray emissions from polyethylene nanowire array targets irradiated by femtosecond laser pulses at the intensity of 4×1019 W/cm2. The experimental results indicate more than one order of magnitude enhancement of the water-window x-ray emissions from the nanowire array targets compared to the planar targets. The highest energy conversion efficiency from laser to water-window x-rays is measured as 0.5%/sr, which comes from the targets with the longest nanowires. Supported by particle-in-cell simulations and atomic kinetic codes, the physics that leads to the high conversion efficiency is discussed.
© 2021 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
1. Introduction
The developments of high-intensity laser technologies have opened the door to laser-driven light sources with photon energies from 10$^{-2}$ eV (THz radiation) to 10$^{7}$ eV (gamma-rays) [1,2]. Photons with the energies of $285\sim 540$ eV ($\lambda \approx 2.3\sim 4.4$ nm), also defined as the water-window (WW) x-rays, are ideal to image the inner structure of live cells in vivo with high spatial resolutions as they can penetrate the water while strongly be absorbed by the carbon atoms [3,4]. Laser-driven WW x-ray sources have the advantages of micrometer source sizes, ultrashort durations and high brightness [5]. Further improving the conversion efficiency from laser to WW x-rays is one key issue for the development of laser-driven laboratory WW x-ray microscopes, which can be achieved by utilizing novel targets. Besides regular planar solid targets [6–8], plenty of novel targets such as liquid jet targets [9], gas-puff targets [10,11], carbon nanotube targets [12] and low-density foam targets [13,14] have been studied. Some of them showed appealing conversion efficiency from laser to WW x-rays.
As a kind of novel targets, nanowire array (NWA) targets have been used in high-power laser experiments for the enhanced generation of hot electrons [15], energetic ions [16,17], x-ray emissions [18,19] and neutrons [20]. Unlike planar targets where the laser pulses only heat the surface of the targets, the laser can penetrate into the NWA targets and interact with the side wall of the nanowires. As a result of such volumetric heating, the laser absorption of NWA targets is very high [21]. Irradiated by ultrashort laser pulses with the intensity exceeding 10$^{18}$ W/cm$^{2}$, the nanowires can turn to high-energy-density plasmas with keV temperatures and near-solid densities. The relatively large volumes of the plasmas result in a long hydrodynamic cooling time of $T_h$. Here $T_h=L/C_s$, where $L$ is the plasma size and $C_s$ is the acoustic velocity [19]. As a result, the radiative cooling time $T_r$ is shorter than $T_h$, which means a large portion of plasma energy can be converted to x-ray emissions. A record conversion efficiency of 20% from the laser to x-rays with the photon energy exceeding 1 keV has been reported using Au NWA targets [19].
The wavelength of x-rays from the NWA targets is determined by the materials of the targets. Most NWA targets in previous studies were synthesized by electro-depositing metal atoms into anodized alumina oxide (AAO) membranes. The wavelengths of the emitted x-rays from the metal NWA targets are mainly in the range of $0.1-0.8$ nm. For example, Purvis et al. measured the x-rays in the wavelength range of $0.4-0.6$ nm from Au NWA targets [18]. X-ray emissions around 0.15 nm were also reported from Ni and Co NWA targets [18,22]. For Si NWA targets, the wavelengths of emitted x-rays extended to $0.6-0.8$ nm [17,23]. All the above x-ray emissions were not in the WW region.
In this paper, we utilize polyethylene (PE) NWA targets prepared by the heat-extrusion method instead of the electro-deposition method to generate WW x-rays around 3.5 nm. Experimental results show that the yield of WW x-rays from the PE NWA targets is more than one order of magnitude higher than that from the planar targets. The influence of the nanowires’ lengths on x-ray emissions is experimentally investigated as well. We also perform a series of simulations to study the emission processes of WW x-rays from the NWA targets.
2. Experimental set-up
The experiments were performed at Peking University utilizing the CLAPA laser system [24]. As depicted in Fig. 1(a), a 30 fs laser pulse with the central wavelength of 800 nm was focused on the targets with 90° incident angle by an f/3 off-axis parabolic mirror (OAP). The CLAPA laser facility contains a cross-polarized wave (XPW) system to achieve a nanosecond contrast of $10^{10}$. To prevent the expansion of nanowires caused by the prepulses and amplified spontaneous emissions (ASE), we also employed a plasma mirror system to improve the laser contrast to $10^{-12}$ at 40 ps before the main pulse. The on-target laser energy was about 1.0 J. Considering the full width at half maximum (FWHM) spot size of 4.0 µm $\times$ 4.5 µm with an energy concentration ratio of 30%, the peak intensity of the laser was 4×10$^{19}$ W/cm$^{2}$. The corresponding maximum electric field was $E=$ 1.6×10$^{13}$ V/m, which is strong enough to realize field ionization of carbon to C$^{6+}$[25].
![figure: Fig. 1.](/images/ajax-loader-big.gif)
Fig. 1. The experimental set-up. a) A schematic diagram of the laser and the NWA targets. The laser incidence angle is 90°. A flat-field grazing-incidence spectrometer is placed at 45° to the laser axis in the reflection direction to measure the x-ray emissions. b) and c) SEM images of the PE NWA targets with different lengths of nanowires.
Two kinds of PE NWA targets with the nanowires’ diameters of 200 nm and 500 nm were used in the experiments. The nanowires’ lengths varied from 2 µm to 10 µm. Under the nanowires, 0.2 mm thick PE foils were employed as supporting substrates. Planar PE foils with the thickness of 0.2 mm were also shot for comparison. The NWA targets were prepared by the heat-extrusion method with the following steps. First, we attached a PE sheet on a suitable AAO template composed of uniform parallel pores. Second, the PE-attached AAO templates were heated and mechanically compressed in vacuum so that the PE molecules were extruded into the pores of the template. Third, the NWA targets were obtained by dissolving the AAO templates in NaOH solutions. The scanning electron microscope (SEM) images of the PE NWA targets are displayed in Fig. 1(b) and (c). As one can see, most nanowires stand straight and are isolated from each other. The diameters (D), interval spaces (S) and lengths (L) of the nanowires, as depicted in Fig. 1(a), are determined by the templates. The interval spaces of the 200-nm-diameter and 500-nm-diameter NWA targets are 450 nm and 800 nm, respectively. In order to precisely place the targets on the laser focal spot, a motorized target positioning system was employed with an accuracy of 2 µm [26].
The x-ray emissions from the NWA targets and the planar targets were measured by a flat-field grazing-incidence spectrometer at 45$^\circ$ to the laser axis in the reflection direction. A 1200 lines/mm laminar-type soft x-ray diffraction grating (Shimadzu 30-005) was employed in the spectrometer. The WW x-ray spectra were recorded on-line using an x-ray charge-coupled device (CCD) camera (Andor DO940P-DN). The distance from the targets to the 55-$\mathrm {\mu }$m-wide entrance slit of the spectrometer was 0.98 m. Considering the width of the entrance slit, the spectral resolution of the flat-field spectrometer is about 0.015 nm in the wavelength ranging from 3.1 nm to 4.4 nm. Before the entrance slit, a magnet with a length of 5 cm and a field strength of 0.67 T was placed to deflect the ions and electrons generated from laser-plasma interaction.
3. Results
Figure 2(a)-(c) display the typical raw data of the WW soft x-ray emissions measured by the flat-field spectrometer from the planar targets, NWA targets with the nanowires’ diameters of 200 nm and 500 nm, respectively. Compared to the planar targets, a pronounced enhancement of x-ray emissions from the NWA targets can be observed. Taking into account the acceptance angle of the spectrometer, the diffraction efficiency of the flat-field grating [27,28] and the quantum efficiency of the x-ray CCD [29], we can obtain the x-ray spectra with the absolute spectral response as shown in Fig. 2(d). Here a 4$\pi$ solid angle of the x-ray radiation is assumed. The spectra of WW x-rays with the wavelength range of 2.3 nm to 3.1 nm are not included due to the extreme aberration of the spectrometer. As one can see, more than one order of magnitude enhancement on the x-ray emissions from both NWA targets over the planar targets is demonstrated. The 500-nm-diameter NWA targets have stronger emissions than that of the 200-nm-diameter NWA targets. A slight drop of the spectra around 4.3 nm can be observed due to the existence of a contamination layer on the grating. The contamination effect will slightly reduce the diffraction efficiency of the grating and result in a minor underestimation of the WW x-rays’ yield [30].
![figure: Fig. 2.](/images/ajax-loader-big.gif)
Fig. 2. The single-shot WW x-ray spectra. a), b) and c) The raw data recorded by the x-ray CCD from planar targets, 200-nm-diameter NWA targets, and 500-nm-diameter NWA targets, respectively. The nanowires’ lengths of the targets in b) and c) are both 5 µm. d) The corresponding x-ray spectra of a) - c).
The measured WW x-rays are composed of continuum emissions and line emissions from carbon ions. The continuum emissions are from the recombination of free electrons with carbon ions and the bremsstrahlung radiation. At the laser intensity of 4×10$^{19}$ W/cm$^{2}$, MeV relativistic electrons can be generated from the nanowires’ surface and deposit their energy in nearby nanowires. So the bremsstrahlung radiation is significantly higher than that at lower intensities [6], contributing to a stronger continuum emission. The K$_\alpha$ emission at 4.48 nm is not observed either from the planar or NWA targets, as Auger decay is the dominant process to the radiative one for carbon atoms [31]. The two main lines riding over the strong continuum emission have the central wavelength of 3.37 nm and 4.03 nm, corresponding to the Ly$_\alpha$ and He$_\alpha$ emissions from C$^{5+}$ and C$^{4+}$, respectively. We speculate the relativistic driving laser leads to a quick field ionization of carbon atoms to C$^{4+}$ - C$^{6+}$ in the targets’ surface, resulting in the strong Ly$_\alpha$ and He$_\alpha$ emissions. At the same time, the Auger-decay channel is suppressed due to the lack of outer-shell electrons after the quick field ionization.
We also studied the dependence of the nanowires’ diameters and lengths on the yields of WW x-ray emissions. The yields are calculated from the integral of the WW x-ray spectra in the wavelength range of 3.1 nm to 4.4 nm. As shown in Fig. 3, for the same length of nanowires, the yields of WW x-ray emissions are similar for the 500-nm-diameter and 200-nm-diameter NWA targets. This phenomenon can be interpreted by the similar laser absorption ratio for both the targets. The laser absorption is mainly determined by the total area of the nanowires’ side walls interacted with the laser. In the same laser focal spot, the number of nanowires and the side wall area of each nanowire are proportional to $\textrm {S}^{-2}$ and $\pi \textrm {D}$, respectively. As a result, the total side-wall area is proportional to $\pi \textrm {D/S}^2$. For the 200-nm-diameter NWA targets with S of 450 nm, $\pi \textrm {D/S}^2=3.1\times 10^{-3}/\textrm {nm}$. While for the 500-nm-diameter ones with S of 800 nm, $\pi \textrm {D/S}^2= 2.5\times 10^{-3}/\textrm {nm}$, which is quite close to the 200-nm-diameter case. Figure 3 also indicates that the yields of WW x-rays rise with the increase of the nanowires’ lengths. The conversion efficiency from laser to WW x-rays reaches 0.5%/sr, or 6% assuming a 4$\pi$ solid angle for the optimal 10-${\rm \mu} m$-long NWA targets. When the lengths of nanowires exceed 5 µm, the enhancement becomes less prominent. This tendency can be partly explained by the limited penetrating depth of the driven laser in the NWA targets, which was reported as 6 µm in the previous work [22]. Increasing the lengths of the nanowires from 2 µm to 5 µm can linearly enlarge the interaction volume, which eventually results in a higher laser absorption as well as stronger x-ray emissions. This effect becomes insignificant if the nanowires are longer than the penetrating depth of the laser. Beside the effects of laser absorption, this tendency is also influenced by the plasma opacity. The WW x-rays generated in the deep layer of the targets are hard to escape from the plasma, which results in a saturation length of x-ray yield.
![figure: Fig. 3.](/images/ajax-loader-big.gif)
Fig. 3. Dependence of the WW x-ray yields on the lengths of nanowires for the 200-nm-diameter and 500-nm-diameter NWA targets.
4. Discussion
To investigate the electron heating and WW x-ray emission processes of the NWA targets, we first performed two-dimensional (2D) particle-in-cell (PIC) simulations utilizing the code EPOCH [32]. The simulation box is 6 µm $\times$ 12 µm with a spatial resolution of 2.5 nm $\times$ 2.5 nm. A Gaussian laser pulse travels along the x axis from the left side of the simulation box with a central wavelength of 800 nm. Its normalized vector potential, focal spot size and duration are $a_0=4$, 4 µm and 30 fs, respectively, the same as in the experiments. Here the normalized vector potential is $a_0=eE/m_ec\omega$, where $m_e$, $e$, $E$, $\omega$, and $c$ is the electron mass and charge, the peak electric field strength and angular frequency of laser, as well as the speed of light in vacuum, respectively [33]. The NWA target is also set according to the experimental parameters. The PE plasma is composed of 140 nc electrons, 20 nc protons and 20 nc fully ionized carbons. Here the normalized density $\textrm {n}_{\textrm {c}}=$ 1.7×10$^{21}$ cm−3. The diameter, interval space and length of the nanowires are set as 500 nm, 800 nm and 3 µm, respectively. The nanowires are in the x region of 1 µm to 4 µm. A 1 µm thick PE plasma base is also set in the x region of 4 µm to 5 µm.
Figure 4(a) displays the spatial distribution of the electric field $E_y$ at the simulation time of $t=$ 32 fs. The strong $E_y$ among the nanowires indicates that the driving laser can penetrate the NWA targets and interact with the side wall of the nanowires. As a result, the energy transferred to the electrons in the NWA targets can be enhanced by 4 times compared to that of the planar targets as shown in Fig. 4(b). Another remarkable phenomenon is that $E_y$ decays along the axis of nanowires from 1 µm to 4 µm in Fig. 4(a). It indicates a limited penetrating depth of the driving laser, consistent with the results in Fig. 3.
![figure: Fig. 4.](/images/ajax-loader-big.gif)
Fig. 4. The plasma heating and WW x-ray emission processes. PE NWA targets with the parameters of D = 500 nm, S = 800 nm and L = 3 µm are simulated. a) The spatial distribution of the electric field $E_y$ at the simulation time of $t=$ 32 fs. $E_y$ is normalized by $E_0=m_ec\omega /e=$ 4×10$^{12}$ V/m. The simulation time $t=0$ corresponds to the moment when the laser front edge arrives at the left boundary of the simulation box. b) The ratio of the electron energy $E_{\textrm {electron}}$ to the laser energy $E_{\textrm {laser}}$ in the simulation box for the planar and NWA targets. c) The distribution of the electron temperature at $t=$ 100 fs. d) The energy spectrum of the electrons at $t=$ 100 fs. The fitted bulk electron temperature is 16 keV as shown by the red dashed line. e) Dependence of the mean bound-bound emissivity and charge state per carbon ion on the temperatures of plasmas. Two mass densities of 0.4 g/cm$^{3}$ (solid lines) and 0.004 g/cm$^{3}$ (dashed lines) are calculated from the atomic kinetic code FLYCHK. f) The measured x-ray spectrum as well as the simulated one according to the estimated temporal evolution of the plasmas.
The penetration of the laser in the NWA targets can result in the volumetric heating of the targets as depicted in Fig. 4(c). After the interaction of the laser, the distribution of electron temperature at the simulation time of 100 fs indicates a volumetrically heated plasma. The electron temperature is slightly higher in the center of the laser spot due to the stronger laser field. We integrate the data in Fig. 4(c) to obtain the energy spectrum of the electrons as shown in Fig. 4(d). Considering that the number of high-energy electrons in the tail of the spectrum is very small compared to that of the bulk electrons, we focus on the low-energy but large-amount bulk electrons [34,35]. The hot electrons accelerated in the gaps of the nanowires can be excluded by use of the bulk electrons. The temperature of the bulk electrons in this simulation can be estimated as 16 keV at $t=$ 100 fs as shown by the red dashed line in Fig. 4(d).
The PIC codes can successfully simulate the laser heating process in the NWA targets. However, the emission process of WW x-ray photons is not included in the state-of-the-art PIC simulations. We utilized the atomic kinetic code FLYCHK [36] to investigate the emission process of the laser heated plasmas. Calculations of the x-ray emissions from steady-state carbon plasmas were first performed to study the dependence of the mean bound-bound emissivity and charge state per carbon ion on the temperatures of plasmas. As displayed in Fig. 4(e), one can see that the line emissions of carbon ions mainly happen at the temperature of 100s eV. At higher temperatures, most of the carbon atoms are ionized to C$^{6+}$, which suppresses the probability of line emissions from bound electrons. Figure 4(e) also indicates that the volumetric heating of solid density plasmas is another reason for the high conversion efficiency of NWA targets besides the efficient laser absorption. This can be reflected by the comparison of the bound-bound emissivity between plasmas with the mass densities of 0.4 g/cm$^{3}$ (the mean density of NWA targets) and 0.004 g/cm$^{3}$. The density of a plasma determines the collision frequency as $\nu \propto n_e$, which strongly affect the population distribution of atomic levels and furthermore the emissivity. Compared to low-density plasmas, the high-density NWA plasma has a larger emissivity and a shorter radiative cooling time.
We also performed time-dependent simulations using FLYCHK to tentatively give the WW x-ray spectrum by considering the cooling process of the plasma. The key point is to get the temporal evolution of the plasma’s temperature. We can not directly obtain it from PIC simulations because it requires too many computing resources if we want to simulate the whole process and meanwhile avoid numerical heating in the near-solid-density plasmas. So we use a semiquantitative model to estimate the evolution of the plasma’s temperature. The PIC simulation indicates a hot plasma with the diameter of 10 µm and the bulk electron temperature of 16 keV is formed at $t=$ 100 fs, which however is too hot to efficiently emit WW x-rays. Thereafter, a keV-electrons-driven heat dissipation process happens and results in a larger but colder plasma. This process is quite complicated due to the existence of the magnetic fields in the plasma [37]. For simplicity, we only consider the process after the plasma’s temperature drops below $T_0=$ 600 eV, when efficient WW x-ray emissions happen according to Fig. 4(e). The corresponding plasma diameter $D_0$ can be estimated as $(16000/600)^{1/3}\times 10\approx$ 30 µm. Due to the high collision frequencies of electrons for such low-temperature plasma, a hydrodynamic cooling process will be dominant [18,38]. Assuming the diameter of the hot plasma increases with the cooling time at the electrons’ acoustic velocity of $C_s(t)=\sqrt {2T(t)/m_e}$, which is determined by the instantaneous temperature of the plasma, we have $T_0D_0^3=T(t)D^3(t)$. Here the time-dependent diameter of the hot plasma is $D(t)=D_0+\int _0^t C_s(\tau )d\tau$. With the relationship of $dD(t)/dt=C_s(t)$, the derivative of $T(t)$ can be expressed as
Finally, the temporal evolution of the plasma temperature can be derived as
Using the obtained plasma’s temperature as the input parameter, the time-dependent emissivity can be calculated by FLYCHK. To include the effect of plasma expanding which is not considered in FLYCHK, we multiply the time-dependent size of the emitting area $D^2(t)$ on the FLYCHK results. With the fixed density of the NWA plasma as 0.4 g/cm$^{3}$, the WW spectrum can be obtained by integrating the emissivity at different time as depicted in Fig. 4(f). The measured and simulated spectra fit each other quite well except the continuum part in the wavelength range of 3.1 nm to 3.8 nm, where the calculated spectrum is lower than the measured one. This difference may be due to the underestimate of the bremsstrahlung radiation as we only include the x-ray emissions in FLYCHK after the plasma is colder than 600 eV, while electrons emit much more bremsstrahlung x-rays when the plasma is hotter. Both the intensity ratios of carbon Ly$_\alpha$ line to He$_\alpha$ line are about 1.8 from experiments and simulations, corresponding to an equivalent plasma temperature of 95 eV in the steady-state model. For the more realistic case of a time-dependent plasma, the measured intensity ratio is influenced by the details of the cooling process and 95 eV can be a roughly relevant temperature reflecting this process.
5. Conclusion
In conclusion, we report the WW soft x-ray emissions from PE NWA targets irradiated by femtosecond laser pulses at relativistic intensity. The optimal conversion efficiency in terms of the WW X-rays is measured as 0.5%/sr, which is more than one order of magnitude higher compared to that of the planar targets. The yields of WW x-rays increase with the lengths of nanowires in the targets. We also perform simulations indicating that the high-efficiency generation of WW x-rays from NWA targets can be interpreted by the high laser absorption and the short radiative cooling time in the near-solid-density plasmas. Such a high-efficiency light source using NWA targets may be potential to be utilized in laser-driven laboratory WW x-ray microscopes or lithography while a series of further works need to be done.
Funding
National Grand Instrument Project (2019YFF01014402); NSFC innovation group project (11921006); National Natural Science Foundation of China (11535001, 11775010, 11905286, 61631001).
Acknowledgments
The PIC simulations were carried out in High-Performance Computing Platform of Peking University.
Disclosures
The authors declare no conflict of interest.
References
1. G. Mourou, “Nobel lecture: Extreme light physics and application,” Rev. Mod. Phys. 91(3), 030501 (2019). [CrossRef]
2. O. Renner and F. B. Rosmej, “Challenges of x-ray spectroscopy in investigations of matter under extreme conditions,” Matter Radiat. Extremes 4(2), 024201 (2019). [CrossRef]
3. A. Sakdinawat and D. Attwood, “Nanoscale x-ray imaging,” Nat. Photonics 4(12), 840–848 (2010). [CrossRef]
4. M. Kördel, A. Dehlinger, C. Seim, U. Vogt, E. Fogelqvist, J. A. Sellberg, H. Stiel, and H. M. Hertz, “Laboratory water-window x-ray microscopy,” Optica 7(6), 658 (2020). [CrossRef]
5. F. L. Albert and A. G. R. Thomas, “Applications of laser wakefield accelerator-based light sources,” Plasma Phys. Control. Fusion 58(10), 103001 (2016). [CrossRef]
6. J. Sheil, P. Dunne, T. Higashiguchi, D. Kos, E. Long, T. Miyazaki, F. O’Reilly, G. O’Sullivan, P. Sheridan, and C. Suzuki, “Analysis of soft x-ray emission spectra of laser-produced dysprosium, erbium and thulium plasmas,” J. Phys. B: At., Mol. Opt. Phys. 50(6), 065006 (2017). [CrossRef]
7. G. Arai, H. Hara, T. Hatano, T. Ejima, W. Jiang, H. Ohashi, S. Namba, A. Sunahara, A. Sasaki, M. Nishikino, G. O’Sullivan, and T. Higashiguchi, “Intense water-window soft x-ray emission by spectral control using dual laser pulses,” Opt. Express 26(21), 27748 (2018). [CrossRef]
8. C. John, M. Kishimoto, T. Johzaki, T. Higashiguchi, N. Kakunaka, Y. Matsumoto, N. Hasegawa, M. Nishikino, T. Ejima, A. Sunahara, T. Endo, and S. Namba, “Enhancement of water-window soft x-ray emission from laser-produced Au plasma under low-pressure nitrogen atmosphere,” Opt. Lett. 44(6), 1439 (2019). [CrossRef]
9. J. De Groot, O. Hemberg, A. Holmberg, and H. M. Hertz, “Target optimization of a water-window liquid-jet laser-plasma source,” J. Appl. Phys. 94(6), 3717–3721 (2003). [CrossRef]
10. M. Müller, F.-C. Kühl, P. Großmann, P. Vrba, and K. Mann, “Emission properties of ns and ps laser-induced soft x-ray sources using pulsed gas jets,” Opt. Express 21(10), 12831 (2013). [CrossRef]
11. P. W. Wachulak, A. Bartnik, L. Wegrzynski, J. Kostecki, R. Jarocki, T. Fok, M. Szczurek, and H. Fiedorowicz, “Sub 1-µm resolution "water-window" microscopy using a compact, laser-plasma SXR source based on a double stream gas-puff target,” Nucl. Instrum. Methods Phys. Res., Sect. B 311, 42–46 (2013). [CrossRef]
12. T. Nishikawa, S. Suzuki, Y. Watanabe, O. Zhou, and H. Nakano, “Efficient water-window X-ray pulse generation from femtosecond-laser-produced plasma by using a carbon nanotube target,” Appl. Phys. B: Lasers Opt. 78(7-8), 885–890 (2004). [CrossRef]
13. U. Chakravarty, B. S. Rao, V. Arora, A. Upadhyay, H. Singhal, P. A. Naik, J. A. Chakera, C. Mukherjee, and P. D. Gupta, “Enhanced water window x-ray emission from in situ formed carbon clusters irradiated by intense ultra-short laser pulses,” Appl. Phys. Lett. 103(5), 054107 (2013). [CrossRef]
14. H. Hara, H. Kawasaki, T. Tamura, T. Hatano, T. Ejima, W. Jiang, H. Ohashi, S. Namba, A. Sunahara, A. Sasaki, M. Nishikino, G. O’Sullivan, and T. Higashiguchi, “Emission of water-window soft x-rays under optically thin conditions using low-density foam targets,” Opt. Lett. 43(15), 3750 (2018). [CrossRef]
15. A. Moreau, R. Hollinger, C. Calvi, S. Wang, Y. Wang, M. G. Capeluto, A. Rockwood, A. Curtis, S. Kasdorf, V. N. Shlyaptsev, V. Kaymak, A. Pukhov, and J. J. Rocca, “Enhanced electron acceleration in aligned nanowire arrays irradiated at highly relativistic intensities,” Plasma Phys. Control. Fusion 62(1), 014013 (2020). [CrossRef]
16. M. Dozieres, G. M. Petrov, P. Forestier-Colleoni, P. Campbell, K. Krushelnick, A. Maksimchuk, C. McGuffey, V. Kaymak, A. Pukhov, M. G. Capeluto, R. Hollinger, V. N. Shlyaptsev, J. J. Rocca, and F. N. Beg, “Optimization of laser-nanowire target interaction to increase the proton acceleration efficiency,” Plasma Phys. Control. Fusion 61(6), 065016 (2019). [CrossRef]
17. T. Ebert, N. W. Neumann, L. N. Döhl, J. Jarrett, C. Baird, R. Heathcote, M. Hesse, A. Hughes, P. McKenna, D. Neely, D. Rusby, G. Schaumann, C. Spindloe, A. Tebartz, N. Woolsey, and M. Roth, “Enhanced brightness of a laser-driven X-ray and particle source by microstructured surfaces of silicon targets,” Phys. Plasmas 27(4), 043106 (2020). [CrossRef]
18. M. A. Purvis, V. N. Shlyaptsev, R. Hollinger, C. Bargsten, A. Pukhov, A. Prieto, Y. Wang, B. M. Luther, L. Yin, S. Wang, and J. J. Rocca, “Relativistic plasma nanophotonics for ultrahigh energy density physics,” Nat. Photonics 7(10), 796–800 (2013). [CrossRef]
19. R. Hollinger, C. Bargsten, V. N. Shlyaptsev, V. Kaymak, A. Pukhov, M. G. Capeluto, S. Wang, A. Rockwood, Y. Wang, A. Townsend, A. Prieto, P. Stockton, A. Curtis, and J. J. Rocca, “Efficient picosecond x-ray pulse generation from plasmas in the radiation dominated regime,” Optica 4(11), 1344 (2017). [CrossRef]
20. A. Curtis, C. Calvi, J. Tinsley, R. Hollinger, V. Kaymak, A. Pukhov, S. Wang, A. Rockwood, Y. Wang, V. N. Shlyaptsev, and J. J. Rocca, “Micro-scale fusion in dense relativistic nanowire array plasmas,” Nat. Commun. 9(1), 1077 (2018). [CrossRef]
21. H. Habara, S. Honda, M. Katayama, H. Sakagami, K. Nagai, and K. A. Tanaka, “Efficient energy absorption of intense ps-laser pulse into nanowire target,” Phys. Plasmas 23(6), 063105 (2016). [CrossRef]
22. C. Bargsten, R. Hollinger, M. G. Capeluto, V. Kaymak, A. Pukhov, S. Wang, A. Rockwood, Y. Wang, D. Keiss, R. Tommasini, R. London, J. Park, M. Busquet, M. Klapisch, V. N. Shlyaptsev, and J. J. Rocca, “Energy penetration into arrays of aligned nanowires irradiated with relativistic intensities: Scaling to terabar pressures,” Sci. Adv. 3(1), e1601558 (2017). [CrossRef]
23. Z. Samsonova, S. Höfer, V. Kaymak, S. Ališauskas, V. Shumakova, A. PugŽlys, A. Baltuška, T. Siefke, S. Kroker, A. Pukhov, O. Rosmej, I. Uschmann, C. Spielmann, and D. Kartashov, “Relativistic interaction of long-wavelength ultrashort laser pulses with nanowires,” Phys. Rev. X 9, 021029 (2019). [CrossRef]
24. Y. Geng, Q. Liao, Y. Shou, J. Zhu, X. Xu, M. Wu, P. Wang, D. Li, T. Yang, R. Hu, D. Wang, Y. Zhao, W. Ma, H. Lu, Z. Yuan, C. Lin, and X. Yan, “Generating proton beams exceeding 10 MeV using high contrast 60 TW laser,” Chinese Phys. Lett. 35(9), 092901 (2018). [CrossRef]
25. M. V. Ammosov, N. B. Delone, and V. P. Krainov, “Tunnel ionization of complex atoms and atomic ions in electromagnetic field,” Sov. Phys. JETP 64, 1181 (1986). [CrossRef]
26. Y. Shou, D. Wang, P. Wang, J. Liu, Z. Cao, Z. Mei, Y. Geng, J. Zhu, Q. Liao, Y. Zhao, K. Zhu, C. Lin, H. Lu, W. Ma, and X. Yan, “Automated positioning of transparent targets using defocusing method in a laser proton accelerator,” Nucl. Instrum. Methods Phys. Res., Sect. A 927, 236–239 (2019). [CrossRef]
27. T. Yamazaki, E. Gullikson, N. Miyata, M. Koike, Y. Harada, S. Mrowka, U. Kleineberg, J. H. Underwood, M. M. Yanagihara, and K. Sano, “Comparison of mechanically ruled versus holographically varied line-spacing gratings for a soft-x-ray flat-field spectrograph,” Appl. Opt. 38(19), 4001 (1999). [CrossRef]
28. C. Dong, S. Morita, M. Goto, and E. Wang, “Extension of wavelength range in absolute intensity calibration of space-resolved EUV spectrometer for LHD diagnostics,” Plasma Fusion Res. 7(0), 2402139 (2012). [CrossRef]
29. https://www.andor.com/scientific-cameras/high-energy-detection.
30. T. H. Dinh, Y. Kondo, T. Tamura, Y. Ono, H. Hara, H. Oikawa, Y. Yamamoto, M. Ishino, M. Nishikino, T. Makimura, P. Dunne, G. O’Sullivan, S. Ohta, K. Kitano, T. Ejima, T. Hatano, and T. Higashiguchi, “Evaluation of a flat-field grazing incidence spectrometer for highly charged ion plasma emission in soft x-ray spectral region from 1 to 10 nm,” Rev. Sci. Instrum. 87(12), 123106 (2016). [CrossRef]
31. M. O. Krause, “Atomic radiative and radiationless yields for K and L shells,” J. Phys. Chem. Ref. Data 8(2), 307–327 (1979). [CrossRef]
32. T. D. Arber, K. Bennett, C. S. Brady, A. Lawrencedouglas, M. G. Ramsay, N. J. Sircombe, P. Gillies, R. G. Evans, H. Schmitz, A. R. Bell, and C. P. Ridgers, “Contemporary particle-in-cell approach to laser-plasma modelling,” Plasma Phys. Control. Fusion 57(11), 113001 (2015). [CrossRef]
33. A. Macchi, M. Borghesi, and M. Passoni, “Ion acceleration by superintense laser-plasma interaction,” Rev. Mod. Phys. 85(2), 751–793 (2013). [CrossRef]
34. M. Sherlock, “Universal scaling of the electron distribution function in one-dimensional simulations of relativistic laser-plasma interactions,” Phys. Plasmas 16(10), 103101 (2009). [CrossRef]
35. O. N. Rosmej, Z. Samsonova, S. Höfer, D. Kartashov, C. Arda, D. Khaghani, A. Schoenlein, S. Zähter, A. Hoffmann, R. Loetzsch, A. Saevert, I. Uschmann, M. E. Povarnitsyn, N. E. Andreev, L. P. Pugachev, M. C. Kaluza, and C. Spielmann, “Generation of keV hot near-solid density plasma states at high contrast laser-matter interaction,” Phys. Plasmas 25(8), 083103 (2018). [CrossRef]
36. H. K. Chung, M. H. Chen, W. L. Morgan, Y. Ralchenko, and R. W. Lee, “FLYCHK: Generalized population kinetics and spectral model for rapid spectroscopic analysis for all elements,” High Energy Density Phys. 1(1), 3–12 (2005). [CrossRef]
37. Y. Yang, B. Li, Y. Wu, B. Zhu, B. Zhang, Z. Zhang, M. Yu, F. Lu, K. Zhou, L. Shan, L. Cao, Z. Zhao, W. Zhou, and Y. Gu, “Manipulation and optimization of electron transport by nanopore array targets,” Plasma Sci. Technol. 23(1), 015001 (2021). [CrossRef]
38. D. Rolles, “Highly efficient nanoscale X-ray sources,” Nat. Photonics 12(2), 62–63 (2018). [CrossRef]